0
OPA4H014-SEP
  • OPA4H014-SEP
  • OPA4H014-SEP
  • OPA4H014-SEP

OPA4H014-SEP

ACTIVE

Radiation-tolerant, 11-MHz, low-noise, precision rail-to-rail output JFET amplifier

Texas Instruments OPA4H014-SEP Product Info

1 April 2026 5

Parameters

Number of channels

4

Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V)

18

Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V)

4.5

Vos (offset voltage at 25°C) (max) (mV)

0.12

Offset drift (typ) (µV/°C)

0.35

Input bias current (max) (pA)

10

GBW (typ) (MHz)

11

Slew rate (typ) (V/µs)

20

Rail-to-rail

Out

Iq per channel (typ) (mA)

1.8

Vn at 1 kHz (typ) (nV√Hz)

5.8

CMRR (typ) (dB)

140

Rating

Space

Operating temperature range (°C)

-55 to 125

Iout (typ) (A)

0.03

Architecture

FET

Input common mode headroom (to negative supply) (typ) (V)

-0.1

Input common mode headroom (to positive supply) (typ) (V)

-3.5

Output swing headroom (to negative supply) (typ) (V)

0.2

Output swing headroom (to positive supply) (typ) (V)

-0.2

THD + N at 1 kHz (typ) (%)

0.00005

Package

TSSOP (PW)-14-32 mm² 5 x 6.4

Features

  • Radiation tolerant
    • Single even latch-up (SEL) immune to 43 MeV•cm2/mg
    • ELDRS free to 30 krad(Si)
    • Total ionizing dose (TID) RLAT for every wafer lot up to 30 krad(Si)
  • Space enhanced plastic
    • Au bondwire and NiPdAu lead finish
    • Enhanced mold compound for low outgassing
    • One fabrication, assembly, and test site
    • Extended product life cycle
    • Extended product change notification
    • Product traceability
  • Very-low offset drift: 1 µV/°C maximum
  • Very-low offset: 120 µV
  • Low input bias current: 10 pA maximum
  • Low noise: 5.1 nV/√Hz
  • Slew rate: 20 V/µs
  • Low supply current: 2 mA maximum
  • Input voltage range includes V– supply
  • Wide supply range: 4.5 V to 18 V
  • Radiation tolerant
    • Single even latch-up (SEL) immune to 43 MeV•cm2/mg
    • ELDRS free to 30 krad(Si)
    • Total ionizing dose (TID) RLAT for every wafer lot up to 30 krad(Si)
  • Space enhanced plastic
    • Au bondwire and NiPdAu lead finish
    • Enhanced mold compound for low outgassing
    • One fabrication, assembly, and test site
    • Extended product life cycle
    • Extended product change notification
    • Product traceability
  • Very-low offset drift: 1 µV/°C maximum
  • Very-low offset: 120 µV
  • Low input bias current: 10 pA maximum
  • Low noise: 5.1 nV/√Hz
  • Slew rate: 20 V/µs
  • Low supply current: 2 mA maximum
  • Input voltage range includes V– supply
  • Wide supply range: 4.5 V to 18 V

Description

The OPA4H014-SEP is a low-power JFET input operational amplifier (op amp) that features good drift and low input bias current. With an input range that includes V– and a rail-to-rail output, designers can take advantage of the low-noise characteristics of JFET amplifiers while interfacing to single-supply, precision analog-to-digital converters (ADCs) and digital-to-analog converters (DACs).

The OPA4H014-SEP achieves 11‑MHz unity-gain bandwidth and 20-V/µs slew rate, while consuming only 1.8 mA (typical) of quiescent current. This device runs on a single 4.5‑V to 18‑V supply or dual ±2.25‑V to ±9‑V supplies.

The op amp is built in a plastic, 14‑pin, TSSOP package with radiation hardness up to 43 MeV•cm2/mg (SET) and is ELDRS free up to 30 krad(Si).

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request