Product
0
TPS4141-Q1
  • TPS4141-Q1
  • TPS4141-Q1

TPS4141-Q1

PREVIEW

Automotive 1200V configurable precision resistor divider with integrated switch

Texas Instruments TPS4141-Q1 Product Info

1 April 2026 1

Parameters

FET

Internal

Number of channels

1

Switching voltage (max) (V)

1200

Supply voltage (min) (V)

4.5

Supply voltage (max) (V)

20

Rating

Automotive

Features

Integrated Switching FET, Integrated gain setting

Operating temperature range (°C)

-40 to 125

OFF-state leakage current (µA)

3.5

Package

SOIC (DWQ)-11-106.09 mm² 10.3 x 10.3

Features

  • Qualified for automotive applications
    • AEC-Q100 grade 1: –40°C to 125°C ambient operating temperature
  • Integrated high-voltage resistor divider
    • 30MΩ total resistance, precision matched divider
    • No exposed high-impedance nodes improves measurement integrity from board contaminants
  • Integrated high-voltage disconnect switch
    • 1200V standoff voltage, uni-directional blocking
    • <1.5µA leakage at TA = 105°C
  • High accuracy divider and precision buffer amplifier
    • Buffered output for easy interfacing to analog-to-digital converters
    • Dynamically selectable gain settings to maximize accuracy across high-voltage sensing range
    • Typical gain error ± 0.15%
    • Maximum input offset error ± 220mV
  • Support for uni-directional and bi-directional voltage sensing up to ±1200V
  • Dynamic switching between uni-directional and bi-directional voltage sensing operation
  • Low supply current
    • 5mA ON state current
    • 5.5µA OFF state current
  • SOIC (DWQ-11) package
    • Creepage and clearance ≥8mm from high-voltage sensing pin to all other pins
  • Qualified for automotive applications
    • AEC-Q100 grade 1: –40°C to 125°C ambient operating temperature
  • Integrated high-voltage resistor divider
    • 30MΩ total resistance, precision matched divider
    • No exposed high-impedance nodes improves measurement integrity from board contaminants
  • Integrated high-voltage disconnect switch
    • 1200V standoff voltage, uni-directional blocking
    • <1.5µA leakage at TA = 105°C
  • High accuracy divider and precision buffer amplifier
    • Buffered output for easy interfacing to analog-to-digital converters
    • Dynamically selectable gain settings to maximize accuracy across high-voltage sensing range
    • Typical gain error ± 0.15%
    • Maximum input offset error ± 220mV
  • Support for uni-directional and bi-directional voltage sensing up to ±1200V
  • Dynamic switching between uni-directional and bi-directional voltage sensing operation
  • Low supply current
    • 5mA ON state current
    • 5.5µA OFF state current
  • SOIC (DWQ-11) package
    • Creepage and clearance ≥8mm from high-voltage sensing pin to all other pins

Description

The TPS4141-Q1 is a high-voltage, precision matched resistor divider with an integrated programmable-gain amplifier. The TPS4141-Q1 also integrates a high-voltage switch to allow for connecting or disconnecting the high-voltage sense pin. The device is designed for automotive and industrial applications where accurate, high-voltage measurements are required.

The TPS4141-Q1 programmable-gain amplifier supports four divider ratios using DIV0 and DIV1 inputs. DIV0 and DIV1 can be set to fixed divider ratios and may also be changed dynamically while in operation. This allows for matching the amplifier output (AOUT) to the full-scale input voltage of the analog-to-digital signal chain, improving accuracy over the entire voltage sensing range of interest.

The TPS4141-Q1 supports uni-directional or bi-directional voltage measurement. Bi-directional voltage measurement is supported by supplying an external precision voltage reference from REF to HVGND. Switching between bi-directional and uni-directional voltage sensing during operation is possible using DIV0 and DIV1. Connecting REF to HVGND provides uni-directional voltage sensing only.

The TPS4141-Q1 integrates a high-voltage switch with a standoff voltage greater than 1200V from the high-voltage sense pin (HV) to ground (HVGND). The switch provides uni-directional current blocking from HV to HVGND when disconnected.

The TPS4141-Q1 is a high-voltage, precision matched resistor divider with an integrated programmable-gain amplifier. The TPS4141-Q1 also integrates a high-voltage switch to allow for connecting or disconnecting the high-voltage sense pin. The device is designed for automotive and industrial applications where accurate, high-voltage measurements are required.

The TPS4141-Q1 programmable-gain amplifier supports four divider ratios using DIV0 and DIV1 inputs. DIV0 and DIV1 can be set to fixed divider ratios and may also be changed dynamically while in operation. This allows for matching the amplifier output (AOUT) to the full-scale input voltage of the analog-to-digital signal chain, improving accuracy over the entire voltage sensing range of interest.

The TPS4141-Q1 supports uni-directional or bi-directional voltage measurement. Bi-directional voltage measurement is supported by supplying an external precision voltage reference from REF to HVGND. Switching between bi-directional and uni-directional voltage sensing during operation is possible using DIV0 and DIV1. Connecting REF to HVGND provides uni-directional voltage sensing only.

The TPS4141-Q1 integrates a high-voltage switch with a standoff voltage greater than 1200V from the high-voltage sense pin (HV) to ground (HVGND). The switch provides uni-directional current blocking from HV to HVGND when disconnected.

Subscribe to Welllinkchips !
Your Name
* Email
Popular Posts
Featured Parts More >
Submit a request
CONTACT US
Company address

WELL LINK CHIPS GROUP CO.,LIMITED FLAT/RM 1802 BEVERLY HOUSE 93-107 LOCKHART ROAD WANCHAI HK

Send Enquiry
SEND e-MAIL
Office hour from 9am to 6pm ,
Monday through Friday, UTC/GMT +8