0
BQ24157S
  • BQ24157S
  • BQ24157S

BQ24157S

ACTIVE

I2C 1cell 1.25A Buck battery charger with OTG

Texas Instruments BQ24157S Product Info

1 April 2026 3

Parameters

Rating

Catalog

Number of series cells

1

Cell chemistry

Li-Ion/Li-Polymer

Charge current (max) (A)

1.25

Features

BAT temp thermistor monitoring (hot/cold profile), USB OTG integrated

Vin (min) (V)

4

Vin (max) (V)

6

Absolute max Vin (max) (V)

20

Control topology

Switch-Mode Buck

Battery charge voltage (min) (V)

3.5

Battery charge voltage (max) (V)

4.44

Control interface

I2C

Operating temperature range (°C)

-40 to 125

Package

DSBGA (YFF)-20-3.96 mm² 1.8 x 2.2

Features

  • Integrated Power FETs for up to 1.55-A Charge
    Rate
  • Spread Spectrum Frequency Control for Improved
    EMI Performance
  • High-Accuracy Voltage and Current Regulation
    • Input Current Regulation Accuracy:
      ±5% (100 mA and 500 mA)
    • Charge Voltage Regulation Accuracy:
      ±0.5% (25°C), ±1% (0°C to 125°C)
    • Charge Current Regulation Accuracy: ±5%
  • Factory Test-Mode for GSM Calibration Without a
    Battery
  • Input Voltage Based Dynamic Power
    Management (VIN DPM)
  • Bad Adaptor Detection and Rejection
  • Safety Limit Register for Maximum Charge
    Voltage and Current Limiting
  • High-Efficiency Mini-USB/AC Battery Charger for
    Single-Cell Li-Ion and Li-Polymer Battery Packs
  • 20-V Absolute Maximum Input Voltage Rating
  • 6.5-V Maximum Operating Input Voltage
  • Programmable Charge Parameters through I2C
    Compatible Interface (up to 3.4 Mbps):
    • Input Current Limit
    • VIN DPM Threshold
    • Fast-Charge/Termination Current
    • Charge Regulation Voltage (3.5 to 4.44 V)
    • Low Charge Current Mode Enable/Disable
    • Termination Enable/Disable
  • Synchronous Fixed-Frequency PWM Controller
    Operating at 3 MHz With 0% to 99.5% Duty Cycle
  • Automatic High Impedance Mode for Low Power
    Consumption
  • Robust Protection
    • Reverse Leakage Protection Prevents Battery
      Drainage
    • Thermal Regulation and Protection
    • Input/Output Overvoltage Protection
  • Status Output for Charging and Faults
  • USB Friendly Boot-Up Sequence
  • Automatic Charging
  • Power Up System Without Battery
  • Boost Mode Operation for USB OTG:
    • Input Voltage Range (from Battery):
      3.2 to 4.5 V
    • Output for VBUS: 5.05 V, 350 mA
  • 2.1 × 2.0-mm, 20-Pin DSBGA Package
  • Pin-to-Pin Compatible With bq24157 and bq24158
  • Integrated Power FETs for up to 1.55-A Charge
    Rate
  • Spread Spectrum Frequency Control for Improved
    EMI Performance
  • High-Accuracy Voltage and Current Regulation
    • Input Current Regulation Accuracy:
      ±5% (100 mA and 500 mA)
    • Charge Voltage Regulation Accuracy:
      ±0.5% (25°C), ±1% (0°C to 125°C)
    • Charge Current Regulation Accuracy: ±5%
  • Factory Test-Mode for GSM Calibration Without a
    Battery
  • Input Voltage Based Dynamic Power
    Management (VIN DPM)
  • Bad Adaptor Detection and Rejection
  • Safety Limit Register for Maximum Charge
    Voltage and Current Limiting
  • High-Efficiency Mini-USB/AC Battery Charger for
    Single-Cell Li-Ion and Li-Polymer Battery Packs
  • 20-V Absolute Maximum Input Voltage Rating
  • 6.5-V Maximum Operating Input Voltage
  • Programmable Charge Parameters through I2C
    Compatible Interface (up to 3.4 Mbps):
    • Input Current Limit
    • VIN DPM Threshold
    • Fast-Charge/Termination Current
    • Charge Regulation Voltage (3.5 to 4.44 V)
    • Low Charge Current Mode Enable/Disable
    • Termination Enable/Disable
  • Synchronous Fixed-Frequency PWM Controller
    Operating at 3 MHz With 0% to 99.5% Duty Cycle
  • Automatic High Impedance Mode for Low Power
    Consumption
  • Robust Protection
    • Reverse Leakage Protection Prevents Battery
      Drainage
    • Thermal Regulation and Protection
    • Input/Output Overvoltage Protection
  • Status Output for Charging and Faults
  • USB Friendly Boot-Up Sequence
  • Automatic Charging
  • Power Up System Without Battery
  • Boost Mode Operation for USB OTG:
    • Input Voltage Range (from Battery):
      3.2 to 4.5 V
    • Output for VBUS: 5.05 V, 350 mA
  • 2.1 × 2.0-mm, 20-Pin DSBGA Package
  • Pin-to-Pin Compatible With bq24157 and bq24158

Description

The bq24157S is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small DSBGA package.

The IC charges the battery in three phases: conditioning, constant current, and constant voltage. The input current is automatically limited to the value set by the host.

Charge is terminated based on battery voltage and user-selectable minimum current level. During normal operation, the IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I2C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current after TJ increases to about 125°C. To support a USB OTG device, bq24157S can provide VBUS (5.05 V) by boosting the battery voltage. The IC is available in 20-pin DSBGA package.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request