0
TPS53689T
  • TPS53689T
  • TPS53689T

TPS53689T

ACTIVE

Dual-channel, 8-phase step-down digital multiphase D-CAP+™ controller with VR14 SVID and PMBus

Texas Instruments TPS53689T Product Info

1 April 2026 6

Parameters

Rating

Catalog

Topology

Multiphase

Iout (max) (A)

765

Vin (max) (V)

17

Vin (min) (V)

4.5

Vout (max) (V)

5.5

Vout (min) (V)

0.25

Control mode

D-CAP+

Features

Adjustable current limit, Dynamic Voltage Scaling, Enable, Frequency synchronization, I2C, Light Load Efficiency, Multiple Outputs, PMBus, Phase Interleaving, Power good, Pre-Bias Start-Up, Remote Sense, SVID, Synchronous Rectification, UVLO adjustable, Voltage Margining

Iq (typ) (A)

0.05

Number of phases

8

Operating temperature range (°C)

-40 to 125

Package

WQFN (RSB)-40-25 mm² 5 x 5

Features

  • Input voltage range: 4.5V to 17V
  • Output voltage range: 0.25V to 5.5V
  • Dual output supporting N+M phase configurations (N+M ≤ 8, M ≤ 4)
  • Fully compatible with TI smart power stages
  • Supports voltage- and current-source Imon power stages, with internal 1kΩ resistor
  • Supports dual side power delivery with 12"+ trace length
  • Intel VR14 SVID compliant with PSYS support
  • Backward compatible to VR13.HC/VR13.0 SVID
  • Automatic NVM fault status logging
  • Enhanced D-CAP+ control to provider superior transient performance with excellent dynamic current sharing
  • Dynamic phase shedding with programmable thresholds for optimizing efficiency at light and heavy loads
  • Configurable with non-volatile memory (NVM) for low external component count
  • Individual per-phase IMON calibration, with multi-slope gain calibration to increase system accuracy
  • Diode braking with programmable timeout for reduced transient overshoot
  • Programmable per-phase valley current limit (OCL)
  • PMBus v1.3.1 system interface for telemetry of voltage, current, power, temperature, and fault conditions
  • New soft-shutdown option for overvoltage fault
  • Programmable loop compensation through PMBus
  • 5.00mm × 5.00mm, 40-pin, QFN package
  • Input voltage range: 4.5V to 17V
  • Output voltage range: 0.25V to 5.5V
  • Dual output supporting N+M phase configurations (N+M ≤ 8, M ≤ 4)
  • Fully compatible with TI smart power stages
  • Supports voltage- and current-source Imon power stages, with internal 1kΩ resistor
  • Supports dual side power delivery with 12"+ trace length
  • Intel VR14 SVID compliant with PSYS support
  • Backward compatible to VR13.HC/VR13.0 SVID
  • Automatic NVM fault status logging
  • Enhanced D-CAP+ control to provider superior transient performance with excellent dynamic current sharing
  • Dynamic phase shedding with programmable thresholds for optimizing efficiency at light and heavy loads
  • Configurable with non-volatile memory (NVM) for low external component count
  • Individual per-phase IMON calibration, with multi-slope gain calibration to increase system accuracy
  • Diode braking with programmable timeout for reduced transient overshoot
  • Programmable per-phase valley current limit (OCL)
  • PMBus v1.3.1 system interface for telemetry of voltage, current, power, temperature, and fault conditions
  • New soft-shutdown option for overvoltage fault
  • Programmable loop compensation through PMBus
  • 5.00mm × 5.00mm, 40-pin, QFN package

Description

The TPS53689T is a VR14 SVID compliant step down controller with trans-inductor voltage regulator (TLVR) topology support, two channels, built-in non-volatile memory (NVM), and PMBus interface, and is fully compatible with TI smart power stages. Advanced control features such as the D-CAP+ architecture provide fast transient response, low output capacitance, and good dynamic current sharing. Adjustable control of output voltage slew rate and adaptive voltage positioning are natively supported. In addition, the device supports the PMBus communication interface for reporting the telemetry of voltage, current, power, temperature, and fault conditions to the host system. All programmable parameters can be configured through the PMBus interface and can be stored in NVM as the new default values, to minimize the external component count.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request