0
TPA2001D1
  • TPA2001D1

TPA2001D1

ACTIVE

1-W, mono, analog input Class-D audio amplifier with short-circuit protection

Texas Instruments TPA2001D1 Product Info

1 April 2026 5

Parameters

Audio input type

Analog Input

Architecture

Class-D

Speaker channels (max)

Mono

Control interface

GPIO

Output power (W)

1

Power stage supply (max) (V)

5.5

Power stage supply (min) (V)

2.5

THD + N at 1 kHz (%)

0.1

Load (min) (Ω)

8

Analog supply voltage (min) (V)

2.5

Analog supply voltage (max) (V)

5.5

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Package

TSSOP (PW)-16-32 mm² 5 x 6.4

Features

  • Modulation Scheme Optimized to Operate Without a Filter
  • TSSOP Package Options
  • 1 W Into an 8- Speaker (THD+N<1%)
  • <0.2% THD+N at 1 W, 1 kHz, Into an 8- Load
  • Extremely Efficient Third Generation 5-V Class-D Technology:
    • Low-Supply Current (No Filter) ...4 mA
    • Low-Supply Current (Filter) . . . 7.5 mA
    • Low-Shutdown Current . . . 0.05 µA
    • Low-Noise Floor ...40 µVRMS (No-Weighting Filter)
    • Maximum Efficiency Into 8 , 75 – 85%
    • 4 Internal Gain Settings ...6 – 23.5 dB
    • PSRR . . . –77 dB
  • Integrated Depop Circuitry
  • Short-Circuit Protection (Short to Battery, Ground, and Load)

  • Modulation Scheme Optimized to Operate Without a Filter
  • TSSOP Package Options
  • 1 W Into an 8- Speaker (THD+N<1%)
  • <0.2% THD+N at 1 W, 1 kHz, Into an 8- Load
  • Extremely Efficient Third Generation 5-V Class-D Technology:
    • Low-Supply Current (No Filter) ...4 mA
    • Low-Supply Current (Filter) . . . 7.5 mA
    • Low-Shutdown Current . . . 0.05 µA
    • Low-Noise Floor ...40 µVRMS (No-Weighting Filter)
    • Maximum Efficiency Into 8 , 75 – 85%
    • 4 Internal Gain Settings ...6 – 23.5 dB
    • PSRR . . . –77 dB
  • Integrated Depop Circuitry
  • Short-Circuit Protection (Short to Battery, Ground, and Load)

Description

The TPA2001D1 is a 1-W mono bridge-tied-load (BTL) class-D amplifier designed to drive a speaker with at least 8- impedance. The amplifier uses TI’s third generation modulation technique, which results in improved efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the system level). These features make the device ideal for use in devices where high-efficiency is needed to extend battery run time.

The gain of the amplifier is controlled by two input terminals, GAIN1, and GAIN0. This allows the amplifier to be configured for a gain of 6, 12, 18, and 23.5 dB. The differential input terminals are high-impedance CMOS inputs, and can be used as summing nodes.

The class-D BTL amplifier includes depop circuitry to reduce the amount of turnon pop at power up, and when cycling SHUTDOWN.

The TPA2001D1 is available in the 16-pin TSSOP package that drives 1 W of continuous output power into an 8- load. TPA2001D1 operates over an ambient temperature range of –40°C to 85°C.