0
LMG5126
  • LMG5126
  • LMG5126
  • LMG5126

LMG5126

ACTIVE

42V VIN, 2.5MHz synchronous GaN boost converter with output voltage tracking

Texas Instruments LMG5126 Product Info

1 April 2026 7

Parameters

Rating

Catalog

Topology

Boost

Vin (max) (V)

42

Vin (min) (V)

2.5

Vout (max) (V)

60

Vout (min) (V)

6

Features

Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Analog current monitor, Automatic Light Load Management, Bypass Mode, Chip-enable control pin, Cycle-by-cycle overcurrent protection, External Sync, Fixed PWM Mode, Overcurrent protection with adjustable delay, Power good, Programmable dead time, Spread Spectrum, Tracking

EMI features

Frequency Dithering, Spread Spectrum

Control mode

current mode control

Operating temperature range (°C)

-40 to 125

Iq (typ) (A)

0.0011

Duty cycle (max) (%)

97

Package

VQFN-FCRLF (VBT)-22-24.75 mm² 5.5 x 4.5

Features

  • Input voltage 6.5V to 42V
    • Minimum 2.5V for V(BIAS) ≥ 6.5V or VOUT ≥ 6V
  • Output Voltage 6V to 60V
    • 2% accuracy, internal feedback resistors
    • Bypass operation for VI > VOUT
      • Boot refresh out of audio >20kHz
    • Dynamic output voltage tracking
      • Digital PWM tracking (DTRK)
      • Analog tracking (ATRK)
    • Over voltage protection (65V, 50V, 35V, 25V)
  • Low shutdown ISD of 5µA typical (100uA maximum)
  • Low operating IQ of 1.5mA typical (2.5mA maximum)
  • Stacking with interleaved multiphase operation
    • Up to 4-devices without external clock
  • Switching frequency from 300kHz to 2.5MHz
    • Synchronization to external clock (SYNCIN)
    • Spread Spectrum (DRSS)
  • Dynamically selectable switching modes (FPWM, Diode emulation)
  • Current sense resistor or DCR sensing
  • Average inductor current monitor
  • Average input current limit
  • Selectable current limit (29mV or 60mV)
  • Selectable delay time (DLY)
  • Power good indicator
  • Programmable VI undervoltage lockout (UVLO)
  • Lead-less RLF-22 package with wettable flanks
  • Create a custom design using the LMG5126 with the WEBENCH Power Designer
  • Input voltage 6.5V to 42V
    • Minimum 2.5V for V(BIAS) ≥ 6.5V or VOUT ≥ 6V
  • Output Voltage 6V to 60V
    • 2% accuracy, internal feedback resistors
    • Bypass operation for VI > VOUT
      • Boot refresh out of audio >20kHz
    • Dynamic output voltage tracking
      • Digital PWM tracking (DTRK)
      • Analog tracking (ATRK)
    • Over voltage protection (65V, 50V, 35V, 25V)
  • Low shutdown ISD of 5µA typical (100uA maximum)
  • Low operating IQ of 1.5mA typical (2.5mA maximum)
  • Stacking with interleaved multiphase operation
    • Up to 4-devices without external clock
  • Switching frequency from 300kHz to 2.5MHz
    • Synchronization to external clock (SYNCIN)
    • Spread Spectrum (DRSS)
  • Dynamically selectable switching modes (FPWM, Diode emulation)
  • Current sense resistor or DCR sensing
  • Average inductor current monitor
  • Average input current limit
  • Selectable current limit (29mV or 60mV)
  • Selectable delay time (DLY)
  • Power good indicator
  • Programmable VI undervoltage lockout (UVLO)
  • Lead-less RLF-22 package with wettable flanks
  • Create a custom design using the LMG5126 with the WEBENCH Power Designer

Description

The LMG5126 is a stackable multiphase synchronous boost converter. The device provides a regulated output voltage for lower or equal input voltage also supporting VI to VOUT bypass mode to save power. Up to 4 devices can be stacked with or without external clock.

VOUT can be dynamically programmed using the digital or analog ATRK/DTRK function. VI can be as low as 2.5V after startup as the internal VCC supply is automatically switched from VBIAS to VOUT for VBIAS < 6.5V. The fixed switching frequency is set between 300kHz and 2.5MHz via a resistor on the RT-pin or the SYNCIN clock. The switching modes FPWM or Diode emulation can be changed during operation.

The implemented protections peak current limit, average input current limit, 120% input current limit, average inductor current monitor, over- and undervoltage protection or the thermal shutdown protect the device and the application.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request