0
The ADS8684IDBTR is a four-channel, 16-bit successive-approximation-register (SAR) analog-to-digital converter that integrates the analog front-end functions that would otherwise occupy a separate board section. Each input channel includes overvoltage protection up to ±20 V, a programmable input range that can be selected independently per channel, a constant 1 MΩ resistive input impedance, and an on-chip 4.096 V reference with low temperature drift. The device operates from a single 5 V analog supply while accepting true bipolar input ranges of ±10.24 V, ±5.12 V, and ±2.56 V, as well as unipolar ranges of 0 V to 10.24 V and 0 V to 5.12 V. The aggregate throughput is 500 kSPS, and the SPI-compatible serial interface supports daisy-chaining of multiple devices for multi-board acquisition systems.
The feature set of the ADS8684IDBTR is best understood as a list of external components that the device absorbs into its own package.
Per-channel programmable input ranges: The input range is software-selectable and independent for each of the four channels, covering both bipolar and unipolar spans without an external programmable-gain amplifier or range-switching relay network.
±20 V overvoltage protection on each input: The protection is integrated at the channel level, so an out-of-range fault on one channel does not require external clamping diodes or a series protection resistor that would degrade the 1 MΩ input impedance.
Constant 1 MΩ input impedance across all ranges: Because the input impedance does not change with the selected range, the source loading is predictable and the external driver amplifier can be designed for a fixed load rather than a range-dependent load.
On-chip 4.096 V reference: The internal reference removes the need for an external voltage reference and its associated buffer, and the low drift specification preserves accuracy over the –40°C to 125°C operating range.
Automatic and manual channel scanning: The multiplexer supports both scan modes, allowing the host to either step through channels under software control or let the device sequence them automatically for deterministic sampling.
AUX input with direct ADC connection: The auxiliary input bypasses the multiplexer and connects directly to the ADC, providing a path for a system-level calibration signal or a dedicated DC monitoring channel.
The table below presents the ADS8684IDBTR parameters in three groups: the accuracy metrics that define the measurement quality, the timing metrics that define the acquisition rate, and the interface and power metrics that define the system integration.
|
Category |
Parameter |
Value |
|
Resolution |
ADC architecture |
16-bit SAR |
|
Channel count |
Analog inputs |
4 |
|
Throughput |
Aggregate sample rate |
500 kSPS |
|
Linearity |
DNL / INL |
±0.5 LSB / ±0.75 LSB |
|
Dynamic range |
SNR / THD |
92 dB / –102 dB |
|
Input range (bipolar) |
Per-channel programmable |
±10.24 V, ±5.12 V, ±2.56 V |
|
Input range (unipolar) |
Per-channel programmable |
0–10.24 V, 0–5.12 V |
|
Input impedance |
Constant across ranges |
1 MΩ |
|
Overvoltage protection |
Per input channel |
Up to ±20 V |
|
Reference |
On-chip |
4.096 V, low drift |
|
Analog supply |
Single supply |
5 V |
|
Digital I/O supply |
Separate supply |
1.65 V to 5.25 V |
|
Power dissipation |
Typical |
65 mW |
|
Interface |
Serial |
SPI-compatible, daisy-chain capable |
|
Temperature range |
Operating |
–40°C to 125°C |
|
Package |
TSSOP |
38-pin, 9.7 mm × 4.4 mm |
The signal path of the ADS8684IDBTR begins at the input pin, where the ±20 V overvoltage protection clamps the input before it reaches the multiplexer. From the multiplexer, the selected channel is routed to the analog front-end, which scales the input to the internal ADC full-scale range according to the software-selected range. The front-end gain is trimmed for each range to preserve DC precision, and because the input impedance is a constant 1 MΩ, the source does not see a range-dependent load change. The SAR ADC performs the 16-bit conversion, and the result is made available over the SPI-compatible serial interface. The digital supply operates independently from 1.65 V to 5.25 V, allowing the device to interface directly to 1.8 V, 3.3 V, or 5 V host controllers without level shifters. The AUX input provides a direct path to the ADC that bypasses the multiplexer, which is useful for measuring the internal reference or an external calibration voltage without consuming one of the four main channels.
The ADS8684IDBTR is the right converter when the system needs 16-bit precision across four channels with input signals that may span ±10 V or 0–10 V, and when the board cannot accommodate the external protection, range-switching, and reference circuitry that a discrete signal chain would require. The 500 kSPS aggregate throughput means that each channel can be sampled at 125 kSPS in a round-robin scan, which is sufficient for many industrial monitoring and control loops but not for simultaneous multichannel acquisition at high per-channel rates. If simultaneous sampling is required, a multi-ADC architecture or a converter with per-channel track-and-hold is necessary. The integrated overvoltage protection is a decisive advantage in industrial environments where sensor wiring can be subjected to fault voltages; a discrete solution would require series resistors and clamp diodes that would compromise the 1 MΩ input impedance and the DC accuracy. The device is also a strong fit when the host controller runs from a different I/O voltage than 5 V, because the separate digital supply removes the need for external level translation.
The combination of ±20 V protection, programmable bipolar and unipolar ranges, and a 1 MΩ constant input impedance makes the ADS8684IDBTR suited to industrial process control, power-supply monitoring, test and measurement instrumentation, and multichannel sensor interfaces. In power-supply monitoring, the bipolar ranges can accept a current-sense signal that swings both above and below ground, while the unipolar ranges can measure a 10 V bus directly without an external divider. In test equipment, the daisy-chain capability allows multiple ADS8684IDBTR devices to share a single SPI bus, which is useful when the channel count must scale without multiplying the host’s chip-select lines. In sensor interfaces, the per-channel range programmability means that a single board design can accommodate different sensor types by changing register settings rather than changing external components.
The ADS8688EVM-PDK is the evaluation platform for the ADS868x family, and although it is designated for the eight-channel ADS8688, it provides the hardware and software environment for evaluating the four-channel ADS8684 as well. The PDK includes the evaluation board, a precision host interface (PHI) controller board, and computer software that communicates with the ADC over USB for data capture and analysis. A Linux driver (ADS8688SW-LINUX) is available and supports the ADS868x family through the SPI bus and the IIO subsystem, with mainline Linux availability. An IBIS model (SBAM200) and a TINA-TI model (SBAM201) are provided for signal-integrity and analog-front-end simulation, and the ANALOG-ENGINEER-CALC tool can be used to calculate the external driver amplifier requirements and the reference bypass network. For board-level design, the 38-pin TSSOP package requires attention to the analog and digital supply decoupling, and the input protection structure means that the source driver must be able to settle within the acquisition time after a large overvoltage event is removed from the input.