0
The ADS8681IPWR is a single-channel, 16-bit successive-approximation-register analog-to-digital converter that is more accurately described as a complete data acquisition channel in a 16-pin TSSOP package. Its defining architectural commitment is to move the signal-conditioning burden off the board and into the device: the input driver, the overvoltage protection, the precision reference, and the range-selection network are all integrated. What remains outside the package is a 5 V analog supply, a digital I/O supply that can range from 1.65 V to 5 V, and the SPI bus that carries the conversion results. The result is a converter that can be connected to a ±10 V industrial signal without an external instrumentation amplifier, without a range-switching relay, and without a clamp diode network.
The feature list of the ADS8681IPWR is organized around a single principle: every signal-chain function that would normally require a bill-of-materials line item is either integrated or made software-configurable.
Software-programmable input ranges on a 5 V supply: The device accepts true bipolar inputs of ±12.288 V, ±10.24 V, ±6.144 V, ±5.12 V, and ±2.56 V, as well as unipolar spans from 0 V to 12.288 V, 10.24 V, 6.144 V, and 5.12 V. Range selection is performed by writing to an internal register, so a single hardware design can serve multiple sensor interfaces without component changes.
Constant 1 MΩ input impedance across all ranges: The input impedance does not change when the range is switched, which means the source driver sees a fixed load and the settling behavior is predictable regardless of the selected span.
Integrated overvoltage protection to ±20 V: The protection is placed at the device input, so a fault on the field wiring does not reach the ADC core and does not require external series resistors or clamp diodes that would degrade the 1 MΩ input impedance.
On-chip 4.096 V reference with low drift: The internal reference eliminates the external reference IC and its buffer, and the low-drift specification preserves accuracy over the –40°C to 125°C operating range.
multiSPI interface with daisy-chain capability: The serial interface is backward-compatible with conventional SPI and adds daisy-chain support, which allows multiple converters to share a single chip-select line in multi-channel systems.
ALARM output with programmable thresholds: A dedicated alarm pin can be configured to flag high or low threshold violations, providing a hardware-level out-of-range indication without host intervention.
The table below groups the ADS8681IPWR parameters by the design decision each one informs, rather than presenting a flat list of electrical characteristics.
|
Design Consideration |
Parameter |
ADS8681IPWR Value |
|
Measurement precision |
DNL / INL |
±0.4 LSB / ±0.5 LSB |
|
Dynamic performance |
SNR / THD |
92 dB / –107 dB |
|
Throughput |
Maximum sample rate |
1 MSPS |
|
Input flexibility |
Bipolar ranges |
±12.288 V, ±10.24 V, ±6.144 V, ±5.12 V, ±2.56 V |
|
Input flexibility |
Unipolar ranges |
0–12.288 V, 0–10.24 V, 0–6.144 V, 0–5.12 V |
|
Source loading |
Input impedance |
≥ 1 MΩ, constant across ranges |
|
Fault tolerance |
Input overvoltage protection |
Up to ±20 V |
|
Reference |
On-chip reference |
4.096 V, low drift |
|
Supply architecture |
Analog supply / I/O supply |
5 V / 1.65 V to 5 V |
|
Interface |
Serial protocol |
multiSPI, daisy-chain capable |
|
Thermal envelope |
Operating temperature |
–40°C to +125°C |
|
Footprint |
Package |
16-pin TSSOP (PW) |
The signal path begins at the input pin, where the ±20 V protection clamps the incoming voltage before it reaches the programmable front-end. The front-end gain is trimmed per range, so the full-scale signal presented to the SAR core is normalized regardless of whether the selected range is ±2.56 V or ±12.288 V. Because the input impedance remains at 1 MΩ for every range, the source does not experience a load transient when the range is changed. The SAR core performs the 16-bit conversion, and the result is shifted out over the multiSPI interface. The separate I/O supply allows the digital lines to match the host’s logic level without external level shifters, which is particularly useful in systems where the controller runs at 1.8 V or 3.3 V while the analog front-end operates from 5 V. The ALARM function monitors the conversion result against user-programmed high and low thresholds and asserts a pin when the signal exits the valid window, providing a fast path for fault detection that does not depend on the host polling the SPI bus.
The ADS8681IPWR is the appropriate choice when the system needs a single high-precision channel with a bipolar input span that cannot be accommodated by a conventional 5 V SAR ADC, and when the board area or the engineering effort required to build a discrete front-end is a constraint. The software-programmable range is the feature that separates it from fixed-range converters: a single PCB can be configured for ±10 V, ±5 V, or ±2.5 V sensors by changing a register value rather than by populating different gain resistors. The 1 MSPS throughput supports applications that require oversampling for noise reduction or fast transient capture. If the system requires multiple channels, the daisy-chain capability allows several ADS8681IPWR devices to be cascaded on the same SPI bus, but a multi-channel converter with an integrated multiplexer may be more economical when the channels do not need to be sampled simultaneously. The device is not intended for applications that require simultaneous sampling of multiple channels; its value proposition is depth of integration per channel rather than channel density.
The combination of ±20 V protection, 1 MΩ input impedance, and software-selectable ranges makes the ADS8681IPWR suited to industrial process control, power-supply monitoring, and precision instrumentation. In process control, a 4–20 mA loop current can be converted to a voltage by a precision shunt and fed directly into the device without an external amplifier, because the 1 MΩ input impedance does not load the shunt beyond the error budget. In power-supply monitoring, the bipolar ranges can accept a current-sense signal that swings below ground during transients, and the ALARM output can flag an overcurrent event in hardware. In test and measurement equipment, the 92 dB SNR and ±0.5 LSB INL support DC accuracy requirements that would otherwise demand a separate instrumentation amplifier and a higher-resolution ADC. The extended –40°C to 125°C temperature range allows the device to be placed close to the signal source in harsh environments rather than in a temperature-controlled enclosure.
The ADS8681WEVM-PDK is the evaluation platform for the ADS868xW family, and it provides a direct path to characterizing the ADS8681IPWR’s performance. The kit includes the evaluation board and a precision host interface (PHI) controller board that connects to a PC over USB, and the accompanying GUI provides data capture, histogram generation, spectral analysis, and linearity analysis. The GUI also exposes the device configuration registers, allowing the user to step through the input ranges and observe the effect on noise and linearity in real time. An IBIS model is available for signal-integrity simulation, and a TINA-TI reference design can be used to model the input driver requirements. For board-level design, the 16-pin TSSOP package requires attention to the analog supply decoupling and the reference bypass capacitor placement; because the input protection is internal, the external source driver must be able to recover from an overvoltage event within the acquisition time once the fault is removed.