0
OUTLINE
  • The Architectural Premise: Eight Channels, One Instant

  • Feature Inventory: What the Device Integrates and What It Leaves to the Board

  • Parameter Profile: The Numbers That Define the Design Space

  • Functional Description: From the Bipolar Input to the Digital Word

  • Selection Guidance: When Eight-Way Simultaneity Justifies the Footprint

  • Applications: Protection, Power Quality, and Multi-Axis Control

  • Development Support: EVM, GUI, and Interface Evaluation

ADS8568SPMR — Eight-Channel Simultaneous-Sampling 16-Bit SAR ADC with a Programmable Bipolar Front End

19 November 2026     By Ryan 2

The Architectural Premise: Eight Channels, One Instant

The ADS8568SPMR is an eight-channel, 16-bit successive-approximation-register analog-to-digital converter built around a specific architectural commitment: every channel in a conversion cycle captures its input at the same sampling instant. This is not a multiplexed converter with eight inputs sharing a single track-and-hold circuit. The eight channels are organized as four channel pairs, and each pair has its own sample-and-hold and SAR core, allowing simultaneous acquisition across all eight inputs without inter-channel phase delay. For systems where the relative timing of eight sensor signals carries information—three-phase voltages and currents, multi-axis position feedback, or the eight channels of a power-quality analyzer—this simultaneity removes a source of measurement error that cannot be corrected after the fact.

Feature Inventory: What the Device Integrates and What It Leaves to the Board

The ADS8568SPMR is a converter, not a complete signal chain, but the functions it does integrate are chosen to reduce the external component count in industrial data-acquisition designs.

 

True bipolar inputs with a programmable reference: The analog inputs accept single-ended, bipolar signals. The internal reference is programmable and buffered, spanning 0.5 V to 2.5 V or 0.5 V to 3.0 V, which supports input voltage ranges up to ±12 V. The reference range is set by register configuration rather than by an external reference IC and its associated buffer.-1

 

Four channel pairs for flexible simultaneity: The channels are grouped in four pairs. Separate conversion-start signals allow simultaneous sampling on each pair, on four channels, or on all eight channels, depending on how the CONVST_x pins are driven. This gives the system architect the option to sample a subset of channels at a higher aggregate rate when the full eight-channel set is not required on every cycle.

· 

· 

Selectable parallel or serial interface with daisy-chain capability: The host can read the conversion results through a parallel bus or a serial interface, and the serial mode supports daisy-chaining of multiple devices on a shared bus. The interface mode is not fixed at the board level; it is selected by configuration, which allows a single layout to serve different host architectures.


Auto-sleep mode for scalable power: The device supports an auto-sleep mode that reduces power dissipation at low sample rates. At 10 kSPS, the dissipation falls to 32 mW. This is a meaningful feature for battery-backed or energy-conscious industrial monitoring, where the ADC may spend most of its time in a low-rate supervisory mode and wake to full throughput only for transient capture.

 

Pin and software compatibility across resolutions: The ADS8568SPMR is a member of a family that includes 12-bit and 14-bit variants with pin- and software-compatible footprints. A board designed for the 16-bit device can be populated with a lower-resolution member when the system specification permits, without a layout change.

 

Parameter Profile: The Numbers That Define the Design Space

The table below is organized by the subsystem each parameter governs, rather than as a flat electrical-characteristics list.

Subsystem

Parameter

ADS8568SPMR Value

Channel architecture

Simultaneous-sampling channels

8, grouped in 4 pairs

Throughput (parallel)

Maximum data rate per channel

510 kSPS

Throughput (serial)

Maximum data rate per channel

400 kSPS

Resolution

SAR ADC resolution

16 bit

AC performance

SNR / THD

91.5 dB / –94 dB

Input configuration

Input type

Single-ended, true bipolar

Reference

Programmable buffered internal reference

0.5–2.5 V or 0.5–3.0 V

Input span

Maximum range with internal reference

Up to ±12 V

Supply rails

AVDD / DVDD

4.5–5.5 V / 2.7–5.5 V

Power (full rate)

Dissipation

≈335 mW (typical, LQFP)

Power (low rate)

Dissipation in auto-sleep at 10 kSPS

32 mW

Interface

Digital modes

Parallel, serial (SPI-compatible), daisy-chain

Package

Body

64-pin LQFP, 10 mm × 10 mm

Temperature

Operating range

–40°C to +125°C

The supply architecture deserves a separate note. The analog supply operates from 4.5 V to 5.5 V, while the digital supply spans 2.7 V to 5.5 V, allowing the I/O to interface with a 3.3 V host without level shifters. The high-voltage supplies for the bipolar front end (HVDD and HVSS) are separate from the analog core supply, which is why the device can accept signals up to ±12 V while the SAR core itself operates from a conventional 5 V rail.

Functional Description: From the Bipolar Input to the Digital Word

The signal path begins at an analog input that is referenced to the HVSS and HVDD rails rather than to ground. The input is single-ended and bipolar, meaning the signal can swing both above and below the system ground without an external level-shifting amplifier. The programmable reference sets the full-scale span: with a 2.5 V reference, the input range is ±10 V or ±5 V; with a 3.0 V reference, the range extends to ±12 V or ±6 V. The reference itself is generated by an internal source and buffered before it reaches the SAR cores, and it is adjustable in fine steps through a control register. During the acquisition phase, the input sampling capacitor is charged from the source; during conversion, the input current ceases and the input impedance rises above 1 MΩ. The SAR core then performs the bit-by-bit conversion, and the result is placed in the output register for retrieval through the selected interface. In serial mode, the conversion results are shifted out on SDO_A, SDO_B, and SDO_C, with the number of active output ports set by the SEL_x pins.

Selection Guidance: When Eight-Way Simultaneity Justifies the Footprint

The ADS8568SPMR is the right converter when the application requires eight channels of 16-bit data with a known phase relationship and an input span that exceeds the 0–5 V window of a conventional SAR ADC. The simultaneous-sampling architecture is the primary selection criterion: a multiplexed converter would introduce a sampling skew between channels that varies with the scan order and the conversion time, which is unacceptable in power-quality analysis, multi-axis motor control, and protection-relay applications where the phase angle between channels is the measured quantity. The programmable bipolar input is the secondary criterion: the device can be connected directly to ±10 V industrial sensors and ±12 V signal chains without an external difference amplifier, and the range can be changed by register write rather than by component substitution. The trade-off relative to a multiplexed converter is die area and cost; the trade-off relative to a discrete eight-channel signal chain is the loss of per-channel gain and filtering flexibility. For systems that need fewer than eight simultaneous channels, the six-channel ADS8556 family provides a pin-compatible migration path with a different channel count and throughput profile.

Applications: Protection, Power Quality, and Multi-Axis Control

The application list in the data sheet maps directly onto the device’s architectural strengths: protection relays, power-quality measurement, multi-axis motor control, programmable logic controllers, and industrial data acquisition. In a protection relay, the eight simultaneous channels capture the phase voltages and currents of a three-phase feeder at the same instant, allowing the relay to compute symmetrical components and directional power without phase-error correction. In power-quality measurement, the 91.5 dB SNR and –94 dB THD support harmonic analysis up to the fiftieth order and beyond, while the ±12 V input range accommodates the crest factor of distorted mains waveforms. In multi-axis motor control, the channel pairs can be allocated to the phase currents of two motors or to the current and position feedback of a single axis, with the simultaneity preserving the field-orientation angle. The extended –40°C to +125°C temperature range and the 64-pin LQFP package support deployment in sealed industrial enclosures.

Development Support: EVM, GUI, and Interface Evaluation

The ADS8568EVM-PDK is the supported evaluation platform. It includes the evaluation board and the software infrastructure needed to characterize the device without designing a custom board. The EVM GUI is compatible with Windows 7, Windows 8, and Windows 10 in 64-bit versions, and it provides control over the interface mode, the reference configuration, and the channel-pair range settings. The user guide documents the jumper settings for hardware and software modes, including the JP9 and JP12 positions that select the internal reference and the interface configuration. For designers who wish to evaluate the lower-resolution family members, the 12-bit and 16-bit versions are pin-for-pin compatible, and the EVM can be populated with the ADS8528 for software development before committing to the 16-bit device. The EVM data rate is limited by the plug-in software to 400 kSPS, which corresponds to the serial-interface maximum; the full 510 kSPS parallel-mode rate requires a custom capture setup. Layout attention should focus on the HVDD and HVSS decoupling, the reference bypass capacitor, and the separation of the analog input traces from the digital interface lines.

 


About Ryan

Ryan is an Electronic Engineer at Welllinkchips with 12+ years of industry experience. He writes clear, practical resources that help engineering and procurement teams evaluate component specifications, circuit performance, reliability, lifecycle risk, and supplier considerations.

His work is intended to support informed design and purchasing decisions for active, obsolete, and hard-to-source electronic components.

Areas of focus

· Electronic circuit design and component selection

· Obsolete and end-of-life component risk

· Supplier verification and counterfeit-risk reduction

· Component alternatives and BOM continuity

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request