0
The ADS8556IPMR is a 16-bit, six-channel simultaneous-sampling SAR ADC whose internal topology is organized around three channel pairs rather than a single multiplexed input bank. Each pair has its own sample-and-hold circuit and SAR core, and separate conversion-start signals allow the pairs to be sampled independently, in groups of four, or all six at once. This paired architecture is a deliberate compromise between the eight-channel simultaneity of larger converters and the lower pin count and power of a four-channel device. For three-phase systems, the six channels map naturally onto three voltage and three current measurements, and the pairing arrangement allows the voltage and current of a given phase to be acquired in the same conversion window, preserving the phase relationship that power calculations depend on.
The ADS8556IPMR differentiates itself from fixed-range simultaneous-sampling converters through two feature clusters: a flexible input-range selection scheme and a set of power-down modes that scale dissipation with the acquisition duty cycle.
Pin-selectable or register-programmable input ranges up to ±12 V: The input range is set by the RANGE pin in hardware mode or by the RANGE_x bits in software mode, selecting either ±4×VREF or ±2×VREF. With the internal reference at 2.5 V, the spans are ±10 V or ±5 V; with the reference at 3.0 V, they extend to ±12 V or ±6 V. The range can be changed without external component substitution, and the hardware-mode pin selection allows a fixed range to be set at power-up without a configuration sequence.
Internal 2.5 V or 3.0 V reference with 10-bit adjustment: The reference source is followed by a 10-bit DAC that adjusts the reference voltage in 2.44 mV or 2.93 mV steps, depending on the selected reference. This fine adjustment supports system-level gain calibration without an external trim potentiometer.
Three power-down modes: The device offers deep power-down (standby), partial power-down, and auto-nap power-down. These modes allow the system controller to trade wake-up latency against quiescent current, which is relevant in industrial instruments that alternate between measurement bursts and idle periods.
Internal or external conversion clock: In the default configuration, the device generates its own conversion clock. In software mode, an external clock of up to 20 MHz can be applied, which raises the maximum data rate from the internal-clock figures to 800 kSPS in parallel mode and 530 kSPS in serial mode. The external-clock option is useful when multiple converters must be synchronized to a common time base.
Selectable parallel or serial interface with multiple output ports: The parallel interface can be configured for 8-bit or 16-bit bus width. The serial interface provides up to three output ports (SDO_A, SDO_B, SDO_C), and the active port count is selected by the SEL_x pins. This allows the host to choose between a narrow, high-speed serial link and a wider, lower-speed connection without changing the device.
The table below separates the parameters by the operating mode they apply to, because the ADS8556IPMR’s performance is not a single set of numbers but a function of clock source and interface selection.
|
Operating Context |
Parameter |
ADS8556IPMR Value |
|
Channel architecture |
SAR channels |
6, organized as 3 pairs |
|
Internal clock, parallel |
Maximum data rate per channel |
630 kSPS |
|
Internal clock, serial |
Maximum data rate per channel |
450 kSPS |
|
External clock, parallel |
Maximum data rate per channel |
800 kSPS |
|
External clock, serial |
Maximum data rate per channel |
530 kSPS |
|
Resolution and linearity |
Resolution |
16 bit |
|
AC performance |
SNR (ADS8556) |
91.5 dB |
|
Input range (VREF = 2.5 V) |
Pin- or register-selectable |
±10 V or ±5 V |
|
Input range (VREF = 3.0 V) |
Pin- or register-selectable |
±12 V or ±6 V |
|
Reference |
Internal source |
2.5 V or 3.0 V, 10-bit adjustable |
|
Power states |
Available modes |
Deep power-down, partial power-down, auto-nap |
|
Supply rails |
AVDD / DVDD |
4.5–5.5 V / 2.7–5.5 V |
|
Package |
Body |
64-pin LQFP, 10 mm × 10 mm |
|
Temperature |
Operating range |
–40°C to +125°C |
The supply architecture matches the bipolar input capability: the analog core operates from a 5 V rail, while the high-voltage supplies for the input front end are separate, allowing the ±12 V input span without exposing the SAR core to the full signal swing. The digital supply’s 2.7 V to 5.5 V range allows direct connection to 3.3 V hosts, and the typical power consumption is in the 335 mW range at full rate.
The ADS8556IPMR is built from six charge-redistribution SAR ADCs, each with an inherent sample-and-hold function. The analog inputs are single-ended and bipolar, and the selected range determines the input capacitance: 10 pF in the ±4×VREF mode and 20 pF in the ±2×VREF mode. During acquisition, the source must charge this capacitance to the required resolution within the 280 ns acquisition window; during conversion, the input current ceases and the input impedance exceeds 1 MΩ. The conversion clock can be internal or external, and the interface can be parallel or serial, with the parallel bus width selectable as 8 or 16 bits. In serial mode, the three output ports can be activated individually or together, and the conversion results are shifted out MSB-first on the rising edge of SCLK. The power-down modes are controlled through the configuration register in software mode or through pin states in hardware mode, allowing the device to enter a low-quiescent-current state between acquisition bursts.
The ADS8556IPMR occupies a specific point in the simultaneous-sampling converter space: it provides six channels rather than eight, but it adds a level of range and power-management flexibility that fixed-range converters do not offer. The six-channel count is a natural fit for three-phase power measurement, where three voltages and three currents must be acquired together. The pin-selectable range is valuable in systems that must support both ±10 V and ±5 V sensors with the same board design, and the register-based range control in software mode allows the range to be changed per channel pair at run time. The external-clock option raises the throughput ceiling to 800 kSPS in parallel mode, which is higher than the internal-clock maximum of 630 kSPS, and the serial maximum of 530 kSPS with an external clock exceeds the 450 kSPS internal-clock serial rate. The three power-down modes give the system architect tools to reduce average power in duty-cycled instruments without sacrificing the ability to wake quickly for a measurement burst. The trade-off relative to an eight-channel converter is two fewer simultaneous channels; the trade-off relative to a multiplexed converter is higher per-channel cost and a larger package footprint.
The ADS8556IPMR is specified for power-quality measurement, protection relays, multi-axis motor control, programmable logic controllers, and industrial data acquisition. In power-quality instruments, the six channels capture three-phase voltages and currents simultaneously, and the programmable reference allows the full-scale range to be matched to the expected signal amplitude, preserving resolution for low-level harmonic measurements. In protection relays, the simultaneous sampling of all six channels allows the relay to compute phase angles and sequence components without interpolating between channels, which improves the accuracy of directional and distance elements. In multi-axis motor control, the three channel pairs can be allocated to the phase currents of a three-phase inverter and the DC-bus voltage, with the pairing arrangement allowing the current and voltage of each phase to be sampled in the same conversion window. The 64-pin LQFP package and the –40°C to +125°C temperature range support installation in motor drives and industrial control cabinets.
The ADS8556EVM is the evaluation platform for the ADS855x family, and it is designed to accommodate the ADS8556, ADS8557, and ADS8558 devices in the same board footprint. The EVM supports both hardware mode, where the range and interface are set by pin states, and software mode, where the configuration register controls the range, the clock source, and the power-down state. The evaluation software runs on Windows 7, 8, and 10 and provides a register-level interface for configuring the device and capturing conversion data. The EVM is factory-configured for ±12 V analog operation and can interface with the 5-6K Interface Board for C5000 and C6000 DSP platforms. In software mode, an external conversion clock must be applied to the SMA connector J6 if the internal clock is not used, and the RANGE setting is controlled by the software register rather than by the pin. For layout, the four-supply architecture (AVDD, DVDD, HVDD, HVSS) requires careful sequencing and decoupling, and the analog input traces should be kept away from the digital interface lines to preserve the 91.5 dB SNR at the maximum sample rate.