Product
0
TXV0106
  • TXV0106
  • TXV0106
  • TXV0106

TXV0106

ACTIVE

Dual-supply fixed-direction six-channel voltage translator

Texas Instruments TXV0106 Product Info

1 April 2026 0

Parameters

Bits (#)

6

Data rate (max) (Mbps)

500

Topology

Push-Pull

Direction control (typ)

Fixed-direction

Vin (min) (V)

1.14

Vin (max) (V)

3.6

Vout (min) (V)

1.14

Vout (max) (V)

3.6

Applications

GPIO, JTAG, RGMII, SPI, UART

Features

Output damping resistors, Output enable, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc disconnect, Vcc isolation, Wettable flanks package

Prop delay (ns)

2.3

Technology family

TXV

Supply current (max) (mA)

0.022

Rating

Catalog

Operating temperature range (°C)

-40 to 125

Package

WQFN (BQB)-16-8.75 mm² 3.5 x 2.5

Features

  • Configurable design allows each port to operate with a power supply range from 1.2 V to 3.6 V

  • Supports up to 500Mbps for 1.65 V to 3.6 V
  • Meets RGMII 2.0 timing specifications:
    • < 750 ps rise and fall time
    • < ± 5 % duty cycle distortion
    • < ± 400 ps channel to channel skew
    • Up to 250Mbps/channel
  • Integrated 10 Ω damping output resistor to minimize signal reflections
  • High drive strength (up to 12 mA at 3.6 V)
  • Fully configurable symmetric dual-rail design
  • Optimal signal integrity performance with 390ps peak-to-peak jitter for 1.8 V to 3.3 V
  • Features VCC isolation and VCC disconnect
  • Ioff supports partial-power-down mode operation
  • Latch-up performance exceeds 100 mA per JESD 78, Class II
  • ESD protection exceeds JESD 22:
    • 2000-V Human-Body Model
    • 1000-V Charged-Device Model
  • Low power consumption:
    • 10-µA maximum (25°C)
    • 20-µA maximum (–40°C to 125°C)
  • Operating temperature from –40°C to +125°C

  • Configurable design allows each port to operate with a power supply range from 1.2 V to 3.6 V

  • Supports up to 500Mbps for 1.65 V to 3.6 V
  • Meets RGMII 2.0 timing specifications:
    • < 750 ps rise and fall time
    • < ± 5 % duty cycle distortion
    • < ± 400 ps channel to channel skew
    • Up to 250Mbps/channel
  • Integrated 10 Ω damping output resistor to minimize signal reflections
  • High drive strength (up to 12 mA at 3.6 V)
  • Fully configurable symmetric dual-rail design
  • Optimal signal integrity performance with 390ps peak-to-peak jitter for 1.8 V to 3.3 V
  • Features VCC isolation and VCC disconnect
  • Ioff supports partial-power-down mode operation
  • Latch-up performance exceeds 100 mA per JESD 78, Class II
  • ESD protection exceeds JESD 22:
    • 2000-V Human-Body Model
    • 1000-V Charged-Device Model
  • Low power consumption:
    • 10-µA maximum (25°C)
    • 20-µA maximum (–40°C to 125°C)
  • Operating temperature from –40°C to +125°C

Description

The TXV0106 is a 6-bit, dual-supply fixed-direction low-skew, low jitter voltage translation device. This device can be used for redriving, voltage translation and power isolation when implementing skew sensitive interface, such as RGMII between Ethernet MAC and PHY. The Ax I/O pins and enable pin (OE) are referenced to VCCA logic levels, and Bx I/O pins are referenced to VCCB logic levels. This device has improved channel-to-channel skew, duty cycle distortion and symmetric rise or fall timing for applications requiring strict timing conditions.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, thus preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC supply is at or near 0V both ports will switch to a high-impedance state. This feature enables power isolation for communications across multiple MACs and PHYs, and is beneficial in situations where MACs and PHYs are powered up asynchronously preventing current backflow between devices.

The TXV0106 transmits data in a fixed direction from the A bus to the B bus. When OE is set to High, both Ax and Bx pins will be forced into a high-impedance state. See Device Functional Modes for a summary of the operation of the control logic.

The TXV0106 is a 6-bit, dual-supply fixed-direction low-skew, low jitter voltage translation device. This device can be used for redriving, voltage translation and power isolation when implementing skew sensitive interface, such as RGMII between Ethernet MAC and PHY. The Ax I/O pins and enable pin (OE) are referenced to VCCA logic levels, and Bx I/O pins are referenced to VCCB logic levels. This device has improved channel-to-channel skew, duty cycle distortion and symmetric rise or fall timing for applications requiring strict timing conditions.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, thus preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC supply is at or near 0V both ports will switch to a high-impedance state. This feature enables power isolation for communications across multiple MACs and PHYs, and is beneficial in situations where MACs and PHYs are powered up asynchronously preventing current backflow between devices.

The TXV0106 transmits data in a fixed direction from the A bus to the B bus. When OE is set to High, both Ax and Bx pins will be forced into a high-impedance state. See Device Functional Modes for a summary of the operation of the control logic.

Subscribe to Welllinkchips !
Your Name
* Email
Popular Posts
Featured Parts More >
Submit a request
CONTACT US
Company address

WELL LINK CHIPS GROUP CO.,LIMITED FLAT/RM 1802 BEVERLY HOUSE 93-107 LOCKHART ROAD WANCHAI HK

Send Enquiry
SEND e-MAIL
Office hour from 9am to 6pm ,
Monday through Friday, UTC/GMT +8