0
TPS542A50
  • TPS542A50
  • TPS542A50

TPS542A50

ACTIVE

4-V to 18-V input, voltage mode, 15-A synchronous SWIFT™ step-down converter with I2C interface

Texas Instruments TPS542A50 Product Info

1 April 2026 4

Parameters

Rating

Catalog

Topology

Buck

Iout (max) (A)

15

Vin (max) (V)

18

Vin (min) (V)

4

Vout (max) (V)

5.5

Vout (min) (V)

0.5

Features

Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Differential Remote Sense, Enable, Forced PWM, Frequency synchronization, I2C, Over Current Protection, Power good, Pre-Bias Start-Up, Soft Start Adjustable, Synchronous Rectification, UVLO Fixed

Control mode

Voltage mode

Operating temperature range (°C)

-40 to 150

Iq (typ) (A)

0.0012

Duty cycle (max) (%)

80

Package

VQFN-HR (RJM)-33-18 mm² 4 x 4.5

Features

  • Integrated 9.1-mΩ and 2.6-mΩ MOSFETs support up to 15-A output current
  • 0.5-V to 5.5-V output voltage range
  • Fixed-frequency voltage control mode with selectable internal compensation
  • Seven selectable frequency settings from 400 kHz to 2.2 MHz
  • Synchronizes to an external clock
  • Fully differential remote sense
  • Device configurable by analog pinstrap resistors or through I2C interface
  • VOUT adjustment with controlled slew rate through I2C from –20% to +10% in 0.028% steps
  • Six selectable overcurrent limits, four soft-start slew rates, and two I2C addresses
  • Monotonic start-up into pre-biased outputs
  • EN pin allowing for adjustable input UVLO
  • Power good indicator
  • 17-µA typical shutdown quiescent current draw
  • Selectable FCCM or PFM for light load efficiency
  • –40 to +150°C operating junction temperature
  • 4-mm × 4.5-mm VQFN package
  • Create a custom design using the TPS542A50 with the WEBENCH Power Designer
  • Integrated 9.1-mΩ and 2.6-mΩ MOSFETs support up to 15-A output current
  • 0.5-V to 5.5-V output voltage range
  • Fixed-frequency voltage control mode with selectable internal compensation
  • Seven selectable frequency settings from 400 kHz to 2.2 MHz
  • Synchronizes to an external clock
  • Fully differential remote sense
  • Device configurable by analog pinstrap resistors or through I2C interface
  • VOUT adjustment with controlled slew rate through I2C from –20% to +10% in 0.028% steps
  • Six selectable overcurrent limits, four soft-start slew rates, and two I2C addresses
  • Monotonic start-up into pre-biased outputs
  • EN pin allowing for adjustable input UVLO
  • Power good indicator
  • 17-µA typical shutdown quiescent current draw
  • Selectable FCCM or PFM for light load efficiency
  • –40 to +150°C operating junction temperature
  • 4-mm × 4.5-mm VQFN package
  • Create a custom design using the TPS542A50 with the WEBENCH Power Designer

Description

The TPS542A50 is a high-efficiency synchronous buck converter with differential remote sense and I2C. This device features fixed-frequency, voltage-control mode with pinstrap selectable internal compensation for reduced system cost and complexity. The PWM can be synchronized to an external clock through the SYNC pin. Other key features include PFM for high light load efficiency, low shutdown quiescent current draw, adjustable UVLO through the EN pin and monotonic start up into pre-biased conditions. This device also features an I2C interface for device configuration and output voltage adjustment. The TPS542A50 is a lead-free device. It is fully RoHS compliant without exemption.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request