0
PGA308
  • PGA308
  • PGA308
  • PGA308

PGA308

ACTIVE

Single Supply, Auto-Zero Sensor Amplifier w/Programmable Gain & Offset

Texas Instruments PGA308 Product Info

1 April 2026 5

Parameters

PGA/VGA

PGA

Number of channels

2

Vs (min) (V)

2.7

Vs (max) (V)

5.5

Input type

Differential

Output type

Single-ended

Input offset drift (±) (typ) (µV/°C)

0.2

Interface type

1-wire, UART

Noise at 1 kHz (typ) (V√Hz)

0.00000005

BW at Acl (MHz)

2

Acl, min spec gain (V/V)

4

Voltage gain (max) (V/V)

80

Gain (max) (dB)

64

Architecture

CMOS

Features

Fault Detection

Vos (offset voltage at 25°C) (typ) (mV)

0.005

Input voltage noise (typ) (µV√Hz)

0.05

Slew rate (typ) (V/µs)

0.6

Iq per channel (typ) (mA)

1.3

Gain error (typ) (%)

0.3

Gain drift (max) (ppm/°C)

6

Rating

Catalog

Operating temperature range (°C)

-40 to 125

Package

VSON (DRK)-10-12 mm² 4 x 3

Features

  • Digital Calibration for Bridge Sensors
  • Offset Select: Coarse and Fine
  • Gain Select: Coarse and Fine
  • Bridge Fault Monitor
  • Input Mux for Lead Swap
  • Over/Under Scale Limits
  • DOUT/VOUT Clamp Function
  • Seven Banks OTP Memory
  • One-Wire Digital UART Interface
  • Operating Voltage: +2.7V to +5.5V
  • Temperature Range: –40°C to +125°C
  • MSOP-10 and 3mm × 4mm DFN-10 Packages
  • Digital Calibration for Bridge Sensors
  • Offset Select: Coarse and Fine
  • Gain Select: Coarse and Fine
  • Bridge Fault Monitor
  • Input Mux for Lead Swap
  • Over/Under Scale Limits
  • DOUT/VOUT Clamp Function
  • Seven Banks OTP Memory
  • One-Wire Digital UART Interface
  • Operating Voltage: +2.7V to +5.5V
  • Temperature Range: –40°C to +125°C
  • MSOP-10 and 3mm × 4mm DFN-10 Packages

Description

The PGA308 is a programmable analog sensor signal conditioner. The analog signal path amplifies the sensor signal and provides digital calibration for offset and gain. Calibration is done via the 1W pin, a digital One-Wire, UART-compatible interface. For three-terminal sensor modules, 1W may be connected to VOUT and the assembly programmed through the VOUT pin. Gain and offset calibration parameters are stored onboard in seven banks of one-time programmable (OTP) memory. The power-on reset (POR) OTP bank may be programmed a total of four times.

The all-analog signal path contains a 2×2 input multiplexer (mux) to allow electronic sensor lead swapping, a coarse offset adjust, an auto-zero programmable gain instrumentation amplifier (PGA), a fine gain adjust, a fine offset adjust, and a programmable gain output amplifier. Fault monitor circuitry detects and signals sensor burnout, overload, and system fault conditions. Over/under-scale limits provide additional means for system level diagnostics. The dual-use DOUT/VCLAMP pin can be used as a programmable digital output or as a VOUT over-voltage clamp.

For detailed application information, see the PGA308 User's Guide (SBOU069) available for download at www.ti.com.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request