0
LM7310
  • LM7310
  • LM7310
  • LM7310
  • LM7310
  • LM7310

LM7310

ACTIVE

2.7-V to 23-V, 28-mΩ, 5.5-A load switch with integrated ideal diode & overvoltage protection

Texas Instruments LM7310 Product Info

1 April 2026 4

Parameters

Vin (max) (V)

23

Vin (min) (V)

2.7

FET

Integrated back-to-back FET

Device type

Ideal diode controller

Number of channels

1

Rating

Catalog

Features

Analog current monitor, Overvoltage protection, Power good signal, Reverse current blocking, Reverse polarity protection, Short circuit protection, Thermal shutdown

Imax (A)

5.5

Iq (typ) (mA)

0.4

Iq (max) (mA)

0.6

Operating temperature range (°C)

-40 to 125

IReverse (typ) (µA)

4.8

Design support

Calculation Tool, EVM, Simulation Model

Shutdown current (ISD) (mA) (A)

0.0046

Product type

Ideal diode controller

Package

VQFN-HR (RPW)-10-4 mm² 2 x 2

Features

  • Wide operating input voltage range: 2.7 V to 23 V
    • 28-V absolute maximum
    • Withstands negative voltages up to -15 V
  • Integrated back-to-back FETs with low On-Resistance: RON = 28.4 mΩ (typ)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage protection
    • 1.2-µs (typ) response time

    • Adjustable overvoltage lockout (OVLO)
  • Fast-trip response to transient overcurrents during steady state
    • 500-ns (typ) response time
    • Latch-off after fault
  • Analog load current monitor output (IMON)
    • Current range: 0.5 A to 5.5 A
    • Accuracy: ±15% (max) (IOUT ≥ 1 A)
  • Active high enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Power Good indication (PG) with adjustable threshold (PGTH)
  • Small footprint: QFN 2 mm x 2 mm, 0.45-mm pitch
  • Wide operating input voltage range: 2.7 V to 23 V
    • 28-V absolute maximum
    • Withstands negative voltages up to -15 V
  • Integrated back-to-back FETs with low On-Resistance: RON = 28.4 mΩ (typ)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage protection
    • 1.2-µs (typ) response time

    • Adjustable overvoltage lockout (OVLO)
  • Fast-trip response to transient overcurrents during steady state
    • 500-ns (typ) response time
    • Latch-off after fault
  • Analog load current monitor output (IMON)
    • Current range: 0.5 A to 5.5 A
    • Accuracy: ±15% (max) (IOUT ≥ 1 A)
  • Active high enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Power Good indication (PG) with adjustable threshold (PGTH)
  • Small footprint: QFN 2 mm x 2 mm, 0.45-mm pitch

Description

The LM73100 is a highly integrated circuit protection and power management solution in a small package. The device provides multiple protection modes using very few external components and is a robust defense against voltage surges, reverse polarity, reverse current and excessive inrush current.

With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the device well suited for power MUX/ORing applications. The device uses linear ORing based scheme to ensure almost zero DC reverse current and emulates ideal diode behavior with minimum forward voltage drop and power dissipation.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Loads are protected from input overvoltage conditions by cutting off the output if input exceeds an adjustable overvoltage threshold. The device also provides fast trip response to transient overcurrent events during steady state.

The device provides an accurate sense of the output load current on the analog current monitor pin.

The device is available in a 2-mm x 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The device is characterized for operation over a junction temperature range of –40°C to +125°C.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request