0
BQ79826Z-Q1
  • BQ79826Z-Q1

BQ79826Z-Q1

PREVIEW

Automotive 26-S battery monitor and balancer with Electrochemical Impedance Spectroscopy engine

Texas Instruments BQ79826Z-Q1 Product Info

1 April 2026 6

Parameters

Rating

Automotive

Number of series cells (max)

26

Number of series cells (min)

9

Features

AEC-Q100 Automotive Qual, ASIL-D, Cell balancing, Electrochemical Impedance Spectroscopy (EIS) Engine, High precision, I2C support, Integrated ADC, Integrated buck converter, Multi-cell support, Open-wire detection, Over-Voltage Protection, Overtemperature protection, Separate MCU requirement, Stackable (built-in interface), Temperature sensing, Under Voltage Protection, Undertemperature protection

Vin (max) (V)

145

Communication interface

Daisy chain, I2C controller, SPI

Operating temperature range (°C)

-40 to 125

Battery overvoltage protection (max) (V)

5.5

TI functional safety category

Functional Safety-Compliant

Package

HTQFP (PZS)-100-196 mm² 14 x 14

Features

  • 26 Channels
    • 26S – 0 to 5.5V range for cell, -2V to 2V range for busbar
    • 143V Abs Max Rating, 9V minimum
    • Busbar support on every channel, except first channel.
    • Stackable up to 128 devices
  • Voltage Accuracy
    • <1.7 mV accuracy, -40 to 125C, Cell: 0V to 5.5V
    • Dedicated ADC per channel. Synchronized redundant measurement.
  • Passive Cell Balancing with integrated FETs up to 300mA odd/even balancing with programmable PWM control
  • Smart EIS Engine
    • Integrated Electrochemical Impedance Spectroscopy measurement engine
    • Impedance Accuracy: 1% (with 1A excitation and 200uΩ impedance)
    • Measurement frequency: 0.01Hz to 3.5kHz
    • < 5us I/V synchronization from device to device
    • Support for global and local excitation
  • Sensor & GPIOs
    • 20 GPIO: Temp Sensor (NTC/PTC), voltage measurement, Interrupt
    • SPI / I2C Interface
    • Temperature Threshold (Active / Sleep)
    • Pressure Threshold / Peak Detector (Active / Sleep)
    • On-chip memory for one-time custom programming
  • Diagnostics & Protection
    • Monitoring
      • Low Power Monitoring Mode (<20uA power consumption)
      • Cell Over-voltage, Under-voltage (OVUV)
      • Cell Over-temperature, Under-temperature (OTUT)
      • 2x die temperature monitors
      • Supply (BAT)
      • Open Wire Detection
    • Reverse Wake Up based on selectable faults
    • Redundancy Paths
      • Cell Voltage
      • GPIO/NTC Voltage
      • Limp Home Mode
    • Diagnostics
      • Automatic diagnostics during cell balancing in active mode
    • Functional Safety Compliant
      • Developed under ISO26262
      • System and hardware capability up to ASIL-D
  • Upgraded Daisy Chain Interface
    • 2Mbps bus speed, Up to 4Mbps with dual SPI
    • <+/-5us device to device synchronization
    • Closed Loop BCI: 200mA, Open Loop BCI: 300mA
    • Isolation: Transformer or capacitor-only
    • FDTI Time: <100ms for 800V packs or 250 cells
    • Support for stack, ring, multidrop, and split-ring
    • Device-to-device automatic communications balancing
  • Power
    • Integrated DC-DC Converter
    • Shutdown: <10uA
    • Sleep Mode with monitoring: As low as 20uA
    • Active Mode: <5mA
  • Package
    • 100-pin QFP, 4mm pitch
    • PowerPad on bottom
  • 26 Channels
    • 26S – 0 to 5.5V range for cell, -2V to 2V range for busbar
    • 143V Abs Max Rating, 9V minimum
    • Busbar support on every channel, except first channel.
    • Stackable up to 128 devices
  • Voltage Accuracy
    • <1.7 mV accuracy, -40 to 125C, Cell: 0V to 5.5V
    • Dedicated ADC per channel. Synchronized redundant measurement.
  • Passive Cell Balancing with integrated FETs up to 300mA odd/even balancing with programmable PWM control
  • Smart EIS Engine
    • Integrated Electrochemical Impedance Spectroscopy measurement engine
    • Impedance Accuracy: 1% (with 1A excitation and 200uΩ impedance)
    • Measurement frequency: 0.01Hz to 3.5kHz
    • < 5us I/V synchronization from device to device
    • Support for global and local excitation
  • Sensor & GPIOs
    • 20 GPIO: Temp Sensor (NTC/PTC), voltage measurement, Interrupt
    • SPI / I2C Interface
    • Temperature Threshold (Active / Sleep)
    • Pressure Threshold / Peak Detector (Active / Sleep)
    • On-chip memory for one-time custom programming
  • Diagnostics & Protection
    • Monitoring
      • Low Power Monitoring Mode (<20uA power consumption)
      • Cell Over-voltage, Under-voltage (OVUV)
      • Cell Over-temperature, Under-temperature (OTUT)
      • 2x die temperature monitors
      • Supply (BAT)
      • Open Wire Detection
    • Reverse Wake Up based on selectable faults
    • Redundancy Paths
      • Cell Voltage
      • GPIO/NTC Voltage
      • Limp Home Mode
    • Diagnostics
      • Automatic diagnostics during cell balancing in active mode
    • Functional Safety Compliant
      • Developed under ISO26262
      • System and hardware capability up to ASIL-D
  • Upgraded Daisy Chain Interface
    • 2Mbps bus speed, Up to 4Mbps with dual SPI
    • <+/-5us device to device synchronization
    • Closed Loop BCI: 200mA, Open Loop BCI: 300mA
    • Isolation: Transformer or capacitor-only
    • FDTI Time: <100ms for 800V packs or 250 cells
    • Support for stack, ring, multidrop, and split-ring
    • Device-to-device automatic communications balancing
  • Power
    • Integrated DC-DC Converter
    • Shutdown: <10uA
    • Sleep Mode with monitoring: As low as 20uA
    • Active Mode: <5mA
  • Package
    • 100-pin QFP, 4mm pitch
    • PowerPad on bottom

Description

The BQ79826Z-Q1 is a new high-cell count 26S stackable battery monitor that includes integrated electrochemical impedance spectroscopy (EIS) engine. The EIS engine provides a new way to detect impedance changes in the cell that allows for monitoring of aging, temperature, SoC, thermal runaway and many other cell parameters. In addition, the device incorporates an intelligent sensor controller to enable easier and more reliable sensor measurements.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request