0
BQ41Z50
  • BQ41Z50
  • BQ41Z50

BQ41Z50

ACTIVE

2 to 4 series Li-ion highly integrated battery fuel gauge and protector

Texas Instruments BQ41Z50 Product Info

1 April 2026 7

Parameters

Cell chemistry

Li-Ion/Li-Polymer, LiFePO4

Number of series cells

2-4 Cells

Communication interface

I2C, SMBus

Battery capacity (min) (mAh)

100

Battery capacity (max) (mAh)

65000

Implementation

Pack

External capacity indication

LED

Features

Cell balancing, Dynamic Z-Track™ technology, ECC authentication, Integrated Protector, SHA-256 Authentication, Turbo Mode

Operating temperature range (°C)

-40 to 85

Cell balancing

External, Internal

Rating

Catalog

Package

WQFN (RSN)-32-16 mm² 4 x 4

Features

  • Fully integrated 2-series, 3-series, and 4-series cell Li-ion, LiPO, or LiFePO4 battery pack manager and protection
  • Ultra-low power 32-bit RISC processor
  • TI Dynamic Z-Track™ algorithm
  • Up to 40V tolerant power supply pins
  • High side N-CH protection FET drive with configurable drive strength
  • Precision analog front-end with two independent 16-bit ADCs:
    • Support for simultaneous current and voltage sampling
    • Support for up to four external thermistor measurements and an internal temperature sensor
  • Primary and secondary levels of protection
    • Overvoltage and undervoltage
    • Overcurrent in charge and discharge
    • Short circuit in discharge
    • Overtemperature
    • Charge timeout
    • CHG and DSG FET drivers
  • Sophisticated charge algorithms
    • JEITA
    • Adaptive charging based on cycle time, run time, and SOH
    • Cell balancing
  • Integrated cell balancing while charging or at rest
  • Supports TURBO mode
  • Diagnostic lifetime data monitor and black box recorder
  • Optional up to three LED display support
  • Supports Elliptic Curve Cryptography (ECC), SHA-2, and SHA-1 authentication
  • Up to 1MHz SMBus v3.2 host communication support
  • Compact package: 32-lead WQFN (RSN)
  • Fully integrated 2-series, 3-series, and 4-series cell Li-ion, LiPO, or LiFePO4 battery pack manager and protection
  • Ultra-low power 32-bit RISC processor
  • TI Dynamic Z-Track™ algorithm
  • Up to 40V tolerant power supply pins
  • High side N-CH protection FET drive with configurable drive strength
  • Precision analog front-end with two independent 16-bit ADCs:
    • Support for simultaneous current and voltage sampling
    • Support for up to four external thermistor measurements and an internal temperature sensor
  • Primary and secondary levels of protection
    • Overvoltage and undervoltage
    • Overcurrent in charge and discharge
    • Short circuit in discharge
    • Overtemperature
    • Charge timeout
    • CHG and DSG FET drivers
  • Sophisticated charge algorithms
    • JEITA
    • Adaptive charging based on cycle time, run time, and SOH
    • Cell balancing
  • Integrated cell balancing while charging or at rest
  • Supports TURBO mode
  • Diagnostic lifetime data monitor and black box recorder
  • Optional up to three LED display support
  • Supports Elliptic Curve Cryptography (ECC), SHA-2, and SHA-1 authentication
  • Up to 1MHz SMBus v3.2 host communication support
  • Compact package: 32-lead WQFN (RSN)

Description

The BQ41Z50 device, incorporating Dynamic Z-Track™ technology, is a fully integrated, single-chip, pack-based solution that provides a rich array of features for gas gauging, protection, and authentication for 2-series, 3-series, and 4-series cell Li-ion, LiPO, and LiFePO4 battery packs.

Using its integrated high-performance analog peripherals and ultra-low power 32-bit RISC processor, the BQ41Z50 device measures and maintains an accurate record of available cell capacity, voltage, current, temperature, and other critical battery parameters and reports them to the system host controller over an SMBus v3.2 compatible interface.

The BQ41Z50 device utilizes Dynamic Z-Track™ technology to report highly accurate state of charge even under dynamic loading conditions. This technology also improves the accuracy of TURBO mode by providing the available max power and max current to the host system.

The BQ41Z50 device provides an array of battery safety functions including overvoltage, overtemperature, overcurrent in discharge, overcurrent in charge, and short circuit in discharge protections. System safety functions incorporate FET protection for the N-CH FETs and cell disconnection detection. The device firmware provides software-based 1st- and 2nd-level safety protection against overvoltage, undervoltage, overcurrent, short circuit current overtemperature conditions. Pack- and cell-related faults are also handled by firmware-based protections.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request