0
AT91SAM9260
  • AT91SAM9260
  • AT91SAM9260

AT91SAM9260

In Production

The ARM®-based SAM9260 running up to 210 MHz embeds Full Speed USB host and device interfaces, a 10/100 Ethernet MAC and an image sensor interface, as well as standard peripherals such as a Multimedia Card Interface (MCI), I2S, USARTs, master/slave SPIs, 16-bit Timers, a TWI and four-channel 10-bit ADC. The external bus interface features controllers for SDRAM and static memories including NAND flash and CompactFlash. The SAM9260 is available in 217-ball LFBGA and 208-pin QFP packages.

Microchip Technology AT91SAM9260 Product Info

16 April 2026 7

Parameters

ADC Resolution (bits)

10

ADC Sampling Rate (ksps)

312

Anti-Tampering Inputs

0

Secure Bootloader

No

CAN/CAN-FD

0

Type of CAN module

None

Camera Interface

Yes

Internal DRAM MB (megabyte)

0

Ext. DRAM Bus

32

Ext. DRAM Interface

SDRAM/LPSDRAM

Number of EBIs

1

ECC bits on NAND interface

1

FPU

No

Graphic LCD Interface

No

Hardware RTCC/RTC

Yes

I/O Pins Max

96

Secure Key Storage (bits)

0

L1 Cache Memory (Data) (KB)

8

L1 Cache Memory (Instructions) (KB)

8

LIN

No

CPU Speed Max MHz (megahertz)

180

NAND Interface

Yes

Operation Voltage Max.(V)

1.95

Operation Voltage Min.(V)

1.65

Internal Oscillator

32KHz

Part Family

SAM9200

QSPI

0

SDIO/SD-CARD/eMMC

2

Temp. Sensor

No

Watch Dog Timer

Yes

Direct Memory Access (DMA) Channels

25

Graphics Controller/GPU

No

Quadrature Encoder Interface

0

ADC Channels

4

Pincount

217

Crypto Engine

No

TempRange Min

-40

TempRange Max

85

Features

  • ARM926 ARM Thumb Processor running up to 210 MHz
  • 8-Kbyte Data Cache, 8-Kbyte Instruction Cache
  • Memory Management Unit
  • 8 Kbytes of SRAM, single-cycle access
  • 32 Kbytes of ROM embedding standard bootstrap
  • 32-bit External Bus Interface (EBI) supporting SDRAM, LPSDRAM, Static Memory, Burst Flash, Glueless Connection to CompactFlash® and NAND Flash/SmartMedia® with 1-bit ECC
  • Enhanced Clock Generator and Power Management Controller
  • On-chip Oscillator with Two PLLs
  • Very Slow Clock Operating Mode and Software Power Optimization Capabilities
  • Two Programmable External Clock Signals
  • System Timer Including Periodic Interrupt, Watchdog and Second Counter
  • Real-time Clock with Alarm Interrupt
  • Debug Unit, Two-wire UART and Support for Debug Communication Channel
  • Advanced Interrupt Controller with 8-level Priority, Individually Maskable Vectored Interrupt Sources, SpuriousInterrupt Protected
  • Seven External Interrupt Sources and One Fast Interrupt Source
  • Three 32-bit PIO Controllers with Up to 96 Programmable I/O Lines, Input Change Interrupt and Open-drain Capability on Each Line
  • 25-channel Peripheral DMA Controller (PDC)
  • ITU-R BT. 601/656 Image Sensor Interface (ISI)
  • Media Independent Interface (MII) or Reduced Media Independent Interface (RMII)
  • Integrated 28-byte FIFOs and Dedicated DMA Channels for Receive and Transmit
  • Dual On-chip Transceivers (Single Port Only on 208-lead PQFP Package)
  • Integrated FIFOs and Dedicated DMA Channels
  • On-chip Transceiver, 2-Kbyte Configurable Integrated FIFOs
  • Automatic Protocol Control and Fast Automatic Data Transfers
  • MMC and SD Memory Card-compliant, Supports Up to Two SD Memory Cards
  • Independent Clock and Frame Sync Signals for Each Receiver and Transmitter
  • I2S Analog Interface Support, Time Division Multiplex Support
  • High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer
  • Support for ISO7816 T0/T1 Smart Card
  • Hardware Handshaking
  • RS485 Support, IrDA® Up To 115 Kbps
  • Full Modem Control Lines on USART1
  • 8 to 16-bit Programmable Data Length
  • 4 External Peripheral Chip Selects
  • Three External Clock Inputs
  • Two Multi-purpose I/O Pins per Channel
  • Double PWM Generation, Capture/Waveform Mode, Up/Down Capability
  • Master Mode Support, All 2-wire Atmel EEPROMs Supported
  • IEEE® 1149.1 JTAG Boundary Scan on All Digital Pins
  • 4-Channel 10-bit ADC
  • 1.65V to 1.95V for VDDCORE, VDDOSC and VDDPLL
  • 3.0V to 3.6V for VDDIOP (Peripheral I/Os) and for VDDIOM (Memory I/Os)
  • 208-pin Green PQFP
  • 217-ball RoHS-compliant LFBGA

Description

The ARM®-based SAM9260 running up to 210 MHz embeds Full Speed USB host and device interfaces, a 10/100 Ethernet MAC and an image sensor interface, as well as standard peripherals such as a Multimedia Card Interface (MCI), I2S, USARTs, master/slave SPIs, 16-bit Timers, a TWI and four-channel 10-bit ADC. The external bus interface features controllers for SDRAM and static memories including NAND flash and CompactFlash. The SAM9260 is available in 217-ball LFBGA and 208-pin QFP packages.

Subscribe to Welllinkchips !
Your Name
* Email
Submit a request